tub spout trim plate not against wall

How to Fix a Bathtub Spout That Does Not Sit Flush With the

If your tub spout isn& 39;t flush against the wall, the pipe nipple to which it& 39;s attached is probably too long. Replace the nipple with a shorter one or cut it. How to Fix a Bathtub Spout That Does Not Sit Flush With the Fiberglass Hunker

Get Price

How to Fill a Tub Spout Gap Home Guides SF Gate

If the gap is wider than 1/2 inch, look for a trim plate that you can install behind the spout. These plates are available at building supply outlets. The opening for the spout is usually offset by

Get Price

Tub spout not against tub wall - DoItYourself.com Community

Try looking under the tub spout and see if there is a slot. This will be where the tub spout is supposed to meet the tub wall. If there is a slot, there should be an allen set screw that holds the spout to the pipe. Unscrew this set screw and you should be able to pull the spout off.

Get Price

How to Fill a Gap Between a Tub Spout Flange and a Fiberglass

Slide the flange over the nipple stubbing out of the wall and screw on the tube spout. On some faucet models, the flange is part of the spout; if so, simply screw on the spout. 2 Tighten the spout

Get Price

GAP repair between tub spout and wall - YouTube

Tub Spout Installation and the Three most important things you must know.Recently I needed a new tub spout. I was shopping Amazon and to my frustration every

Get Price

waterproofing around holes in the wall Archive - Ceramic

as far as the tub spout don& 39;t worry about it. put the plumbers putty on and screw it in. wipe off the extra and you are all set. plumbers putty doesn& 39;t get hard, so you will not have a problem if you want to replace the spout in the future. if you want to caulk after that go ahead. i use a good latex caulk like dap dynaflex230. it comes in many colors and have been using it for years. polyseamseal is another good one but it is an adhesive caulk. gets hard and doesn& 39;t have the flex of some of

Get Price

plumbing - How to fix a huge gap between tub faucet and tile

The ideal method to repair the gap if the spout can not be tightened further, is to shorten the length of the pipe nipple that exits the wall and connects to the spout. You need to un-screw the spout and the pipe nipple. Replace with a shorter nipple equal to the gap measurement.

Get Price

GAP repair between tub spout and wall - YouTube

Tub Spout Installation and the Three most important things you must know.Recently I needed a new tub spout. I was shopping Amazon and to my frustration every

Get Price

waterproofing around holes in the wall Archive - Ceramic

The plates for mixer valves have a foam gasket on the inside the works really well. Plus there is a small weep hole at the bottom of the plate usually that will allow condensation to drip out on the tiled surface. Everything else evaporates. It is not unusual to caulk around the tub spout in a a tub/shower situation. If you use latex caulking

Get Price

Can I Replace My Shower Trim? - Moen Solutions

This may be difficult to remove from the wall as there may be caulking/sealant around the outer edge. *If your shower valve looks like the image below, there is no longer a Moen trim kit available. Replacement parts are still available in limited finishes. If your shower valve does not look like the image above, see Type 1 Valve introduced in 1960

Get Price

Bathroom Ideas: Replace Tub and Shower Faucet Trim DIY

Clean old caulk and dirt off the wall before installing the new controls and spouts. Attach the shower handle replacement and trim in the reverse order that you took them off Photo 3 . Caulk the wall under the rim of the escutcheon plate with acrylic caulk before you tighten it down, when it’s roughly 1/4 in. away from the wall. Leave a 1-in. gap at the bottom, then wipe off excess caulk

Get Price

I would like advice about replacing shower and tub shower

Not sure I understand your answer with respect to the valve trim plate. My sole goal is to update the look of the bathroom. I don& 39;t want to change the way the faucet or the shower behaves. The 25 year old valve seems to be working just fine and, anyway, I don& 39;t have the expertise to replace it. All I want to do is replace the valve trim plate which contains the handle and be sure this will

Get Price

How to Install a Tub Spout - The Seven Trust

If you are replacing a spout with a set screw, apply a thin coat of thread sealant over the pipe optional Apply a small amount of silicone caulk around the back of the spout where it will meet the shower wall, then slide the spout onto the pipe until it is snug to the wall and the opening is level to the bottom of the bathtub you can gauge this by eye or use a torpedo level .

Get Price

LASCO 03-6011 Bathtub Spout with Round Trim Plate, Chrome

LASCO 03-6011 Bathtub Spout, 3 1/2-Inch OD Round Trim Plate, Chrome Plated. Chrome plated finish. Add a decorative flair to a basic tub spout. Covers gaps and holes on finished wall. Finishing trim plate. 3 1/2-Inch outside diameter. Finishing trim plate.

Get Price

50 Most Popular Black Bathtub Faucets for 2021 Seven Trust

This will ensure that the trim plate will cover the cut out hole in the wall. Trims - The trims comprise of well finished handle knobs, handle trims, cartridge covers and spout. Any trim ending in *2450 can be used with this valve. Depending upon the shower model, trims can be of different shape and size, varying from square to circular shower

Get Price

Replacing the tub spout piping Plumbing Zone

If it& 39;s a single lever trace a line around the outside of the trim plate. Remove the trim plate, cut the pex loose. Sweat the pex adapter off or unthread it. Now measure the length of your spout drop, throw a 90 and short piece of pipe on so it sticks out the wall a little long. Test fit. Pull it out and sweat both pieces into the 90. Let it cool.

Get Price

LUDLOW INSTALLATION GUIDELINES

TRIM PLATE FINISHED WALL Figure 4a TRIM PLATE FINISHED WALL NOSE CONE TRIM PLATE O-RING WALL PLATE ¾ IMPORTANT: If the trim plate is not sitting snug to the wall because of uneven tiles, then shimming of the wall plate may be necessary. ¾ If there is too much gap between wall and trim plate: first make sure that the trim plate is fully

Get Price

Bathroom Ideas: Replace Tub and Shower Faucet Trim DIY

Clean old caulk and dirt off the wall before installing the new controls and spouts. Attach the shower handle replacement and trim in the reverse order that you took them off Photo 3 . Caulk the wall under the rim of the escutcheon plate with acrylic caulk before you tighten it down, when it’s roughly 1/4 in. away from the wall. Leave a 1-in. gap at the bottom, then wipe off excess caulk

Get Price

I would like advice about replacing shower and tub shower

Not sure I understand your answer with respect to the valve trim plate. My sole goal is to update the look of the bathroom. I don& 39;t want to change the way the faucet or the shower behaves. The 25 year old valve seems to be working just fine and, anyway, I don& 39;t have the expertise to replace it. All I want to do is replace the valve trim plate which contains the handle and be sure this will

Get Price

How to Install a Tub Spout - The Seven Trust

If you are replacing a spout with a set screw, apply a thin coat of thread sealant over the pipe optional Apply a small amount of silicone caulk around the back of the spout where it will meet the shower wall, then slide the spout onto the pipe until it is snug to the wall and the opening is level to the bottom of the bathtub you can gauge this by eye or use a torpedo level .

Get Price

Shower water leaking into wall at spout - Plbg.com

Re: Shower water leaking into wall at spout; Author: LemonPlumber FL Some tub spout manufacturers offer a trim ring.But you could take a ball off plumbers putty wade it against the wall where the spout pipe comes out ,and install the spout ,this will make a shoulder inside the spout hollow area and could be caulked for effect.Good Luck.Which product number spout are you using?

Get Price

Arrrrrrrrrrgh the tub spout is too short Terry Love

Out of all the acrylic 42x72 tubs sold by Seven Trust& 39;s, I had to find the one messed-up model that needs an exotic spout because the tub& 39;s front was set back too far from the wall by the manufacturer. Making matters worse, I just looked at the tub& 39;s spec sheet again. Nowhere on it does it show the distance from the tile flange to the inside surface of the tub& 39;s front. It shows that the drain is set

Get Price

Pfister Universal Transitional Tub and Shower Trim Kits

This is their universal tub and shower kit. And basically, this is just a trim kit. This box contains no valves. So, you’re going to have to reuse the valves that are in the wall. The only ch is, is that you got to make sure it’s either a Moen, Delta, or Pfister to make sure that the valve trim kit is going to fit.

Get Price

tub/shower escutcheon trim plate not flush with wall

I just bought an Oakbrook tub and shower faucet at Ace Hardware model 48371. The previous faucet was Delta. When I installed it, the valve does not stick very far out of the wall so the trim plate will not go far enough down on it. If the wall was completely removed, the trim plate would still hit the pipes before it came to rest on the base of

Get Price

Escutcheon Plate not sitting against tile

Escutcheon Plate not sitting against tile . chadpsualum. 5 years ago. We are having a contractor redo our bathroom including installation of a new standup shower using the Moen 770 thermostatic valve on both a rain shower and hand-held. In the first pic b

Get Price

LUDLOW INSTALLATION GUIDELINES

TRIM PLATE FINISHED WALL Figure 4a TRIM PLATE FINISHED WALL NOSE CONE TRIM PLATE O-RING WALL PLATE ¾ IMPORTANT: If the trim plate is not sitting snug to the wall because of uneven tiles, then shimming of the wall plate may be necessary. ¾ If there is too much gap between wall and trim plate: first make sure that the trim plate is fully

Get Price

Replacing the tub spout piping Plumbing Zone

If it& 39;s a single lever trace a line around the outside of the trim plate. Remove the trim plate, cut the pex loose. Sweat the pex adapter off or unthread it. Now measure the length of your spout drop, throw a 90 and short piece of pipe on so it sticks out the wall a little long. Test fit. Pull it out and sweat both pieces into the 90. Let it cool.

Get Price

How to Fix a Leaky Bathtub Overflow Tube

If you see leaking, look for signs of water splashing onto the tub spout, showerhead or faucet escutcheon plate valve plate . Cracked or missing caulk around these elements lets water behind the shower wall. If the shower test does not reveal leaks, then the overflow tube is the most likely culprit. My suggested wording in bold below

Get Price

replace a tub or shower faucet with out replacing the tile

I just put the white plastic parts in the wall and tighten the screws till the plate is against the tiles. Now that is it for the Delta Faucet replacement, repair plate, the rest of the chrome trim comes from the faucet you purchased. Install your new faucets trim kit on top of the Delta repair plate and you are done

Get Price

Tub Spout Pipe Loose Behind Wall - YouTube

If you& 39;d like to support the channel, you can do so by shopping for tools or whatever you need on AMAZON through this link, amzn.to/2Dc7pXkIf I& 39;ve pro

Get Price

How to Remove an Old Bathtub Faucet With No Screw eHow

Removing a bathtub faucet with no screw is not as difficult as it may first appear. Many people refer to the bathtub spout as the bathtub faucet. Older bathtub faucet spouts screw onto the bathtub plumbing. Before attempting to unscrew the spout, it is a good idea to make doubly sure no screw is securing the bathtub faucet spout. The screw may

Get Price

Troubleshooting Common Tub Spout Problems DoItYourself.com

The leading cause of tub spout diverter failure is when the spout is used as a foot prop for shaving legs. The tub spout will loosen slightly from the wall and the diverter will not be able to stay in its raised position. You will need to replace the tub spout, and provide a bath stool for the leg-shavers in your family to use when shaving.

Get Price

Sealing tub spout against tub surround? Terry Love Plumbing

In the meantime, even if I get the spout to seal and simultaneously touch the surround wall, is the metal tub spout sitting against the surround wall considered acceptable as this would obviously not be a watertight seal. My concern with this entire installation is that I don& 39;t want water to get behind the spout when someone is showering and find its way into the wall cavity. I have plumbers

Get Price

Tub Spout Pipe Loose Behind Wall - YouTube

If you& 39;d like to support the channel, you can do so by shopping for tools or whatever you need on AMAZON through this link, amzn.to/2Dc7pXkIf I& 39;ve pro

Get Price

replace a tub or shower faucet with out replacing the tile

I just put the white plastic parts in the wall and tighten the screws till the plate is against the tiles. Now that is it for the Delta Faucet replacement, repair plate, the rest of the chrome trim comes from the faucet you purchased. Install your new faucets trim kit on top of the Delta repair plate and you are done

Get Price

Tub and Shower Systems - Moen Solutions

Most Moen fixtures will have the name "Moen" either written or engraved on the handle or escutcheon trim plate behind the handle. For single handle showers and tub/showers, the word Moen will be lo ed on the escutcheon trim plate. For two and three handle showers and tub/showers, the word Moen will be lo ed on the knob handle caps or the small round escutcheon trim plates behind the lever

Get Price

bathtub slip-on diverter spout wiggles - DoItYourself.com

I will add that it& 39;s not a bad idea to seal the spout/wall junction with clear silicone. Leave a little gap in the silicone under the spout so any water that makes it way in can drain out. The silicone will stop any minor wiggling of the spout, as well as prevent splashed water or water from the shower head getting into the wall area.

Get Price

Cart - Moen

The other style is the slip fit tub spout above right . It attaches to ½" copper tubing by slipping on and tightening with a hex wrench. Both tub spouts will have a cut out on the underside near the wall as shown above. If the cut out has a place to insert a hex wrench, you have a slip fit. If the cut out does not have the hex wrench opening

Get Price

Arrrrrrrrrrgh the tub spout is too short Terry Love

Out of all the acrylic 42x72 tubs sold by Seven Trust& 39;s, I had to find the one messed-up model that needs an exotic spout because the tub& 39;s front was set back too far from the wall by the manufacturer. Making matters worse, I just looked at the tub& 39;s spec sheet again. Nowhere on it does it show the distance from the tile flange to the inside surface of the tub& 39;s front. It shows that the drain is set

Get Price

Can I Replace My Shower Trim? - Moen Solutions

This may be difficult to remove from the wall as there may be caulking/sealant around the outer edge. *If your shower valve looks like the image below, there is no longer a Moen trim kit available. Replacement parts are still available in limited finishes. If your shower valve does not look like the image above, see Type 1 Valve introduced in 1960

Get Price

waterproofing around holes in the wall Archive - Ceramic

The plates for mixer valves have a foam gasket on the inside the works really well. Plus there is a small weep hole at the bottom of the plate usually that will allow condensation to drip out on the tiled surface. Everything else evaporates. It is not unusual to caulk around the tub spout in a a tub/shower situation. If you use latex caulking

Get Price

Bathroom Ideas: Replace Tub and Shower Faucet Trim DIY

Clean old caulk and dirt off the wall before installing the new controls and spouts. Attach the shower handle replacement and trim in the reverse order that you took them off Photo 3 . Caulk the wall under the rim of the escutcheon plate with acrylic caulk before you tighten it down, when it’s roughly 1/4 in. away from the wall. Leave a 1-in. gap at the bottom, then wipe off excess caulk

Get Price

Trim Plate Kingston Brass

– Wall Mount Faucets – VIEW ALL; Kitchen Sinks – Undermount Sinks – Drop-In Sinks – Farmhouse Sinks – Wall Mount Sinks – Sink Clips – Side Sprays – VIEW ALL; Accesssories – Soap Dispensers – Kitchen Sink Drains – Disposer Flanges

Get Price

I would like advice about replacing shower and tub shower

Not sure I understand your answer with respect to the valve trim plate. My sole goal is to update the look of the bathroom. I don& 39;t want to change the way the faucet or the shower behaves. The 25 year old valve seems to be working just fine and, anyway, I don& 39;t have the expertise to replace it. All I want to do is replace the valve trim plate which contains the handle and be sure this will

Get Price

How to Install a Tub Spout - The Seven Trust

If you are replacing a spout with a set screw, apply a thin coat of thread sealant over the pipe optional Apply a small amount of silicone caulk around the back of the spout where it will meet the shower wall, then slide the spout onto the pipe until it is snug to the wall and the opening is level to the bottom of the bathtub you can gauge this by eye or use a torpedo level .

Get Price

LASCO 03-6011 Bathtub Spout with Round Trim Plate, Chrome

LASCO 03-6011 Bathtub Spout, 3 1/2-Inch OD Round Trim Plate, Chrome Plated. Chrome plated finish. Add a decorative flair to a basic tub spout. Covers gaps and holes on finished wall. Finishing trim plate. 3 1/2-Inch outside diameter. Finishing trim plate.

Get Price

50 Most Popular Black Bathtub Faucets for 2021 Seven Trust

This will ensure that the trim plate will cover the cut out hole in the wall. Trims - The trims comprise of well finished handle knobs, handle trims, cartridge covers and spout. Any trim ending in *2450 can be used with this valve. Depending upon the shower model, trims can be of different shape and size, varying from square to circular shower

Get Price

Product Details

Product List